Holybro X500 + Pixhawk4 Build

::: info Holybro initially supplied this kit with a Holybro Pixhawk 4), but at time of writing this has been upgraded to a Holybro Pixhawk 6C. This build log is still relevant as the kit assembly is virtually the same, and likely to remain so as the flight controller is upgraded. :::

This topic provides full instructions for building the kit and configuring PX4 using QGroundControl.

Key information

Full Kit: Holybro X500 Kit
Flight controller: Pixhawk 4
Assembly time (approx.): 3.75 hours (180 minutes for frame, 45 minutes for autopilot installation/configuration)

Full X500 Kit

Bill of materials

The Holybro X500 Kit includes almost all the required components:

Pixhawk 4 autopilot
Holybro M8N GPS
Power Management - PM07
Holybro Motors - 2216 KV880 x4 (superseded - check spare parts list for current version).
Holybro BLHeli S ESC 20A x4 (superseded - check spare parts list for current version).
Propellers - 1045 x4 (superseded - check spare parts list for current version).
Battery Strap
Power and Radio Cables
Wheelbase - 500 mm
Dimensions - 410x410x300 mm
433 MHz / 915 MHz Holybro Telemetry Radio

Additionally you will need a battery and receiver (compatible radio system) if you want to control the drone manually.

Main Hardware

This section lists all hardware for the frame and the autopilot installation.

Item | Description | Quantity ---|---|--- Bottom plate | Carbon fiber (2mm thick) | 1 Top plate | Carbon fiber (1.5mm thick) | 1 Arm | Carbon fiber tube (Diameter: 16mm length: 200mm) | 4 Landing gear - Vertical pole | Carbon fiber tube + engineering plastic | 2 Landing gear - Cross bar | Carbon fiber tube + engineering plastic + foam | 2 Motor base | Consists of 6 parts and 4 screws 4 nuts | 4 Slide bar | Diameter: 10mm length: 250mm | 2 Battery mounting board | Thickness: 2mm | 1 Battery pad | 3mm Silicone sheet black | 1 Platform board | Thickness: 2mm | 1 Hanger & rubber ring gasket | Inner hole diameter: 10mm black | 8

X500 Full Package Contents

Electronics

Item Description | Quantity --- | --- Pixhawk4 & Assorted Cables | 1 Pixhawk4 GPS Module | 1 Power Management PM07 (with pre-soldered ESC power cables) | 1 Motors 2216 KV880（V2 Update) | 4 Holybro BLHeli S ESC 20A x4 | 1 433 MHz / 915 MHz Holybro Telemetry Radio | 1

Tools needed

The following tools are used in this assembly:

1.5 mm Hex screwdriver
2.0 mm Hex screwdriver
2.5 mm Hex screwdriver
3mm Phillips screwdriver
5.5 mm socket wrench or small piler
Wire cutters
Precision tweezers

Assembly

Estimate time to assemble is 3.75 hours (180 minutes for frame, 45 minutes for autopilot installation/configuration)

Start by assembling the landing gear. Unscrew the landing gear screws and insert the vertical pole (figures 1 and 2).

Landing Figure 1: Components

Figure 2: Landing gear components

Landing Figure 2: Assembled

Figure 2: Landing gear assembled

Then put the 4 arms through the 4 motor bases shown in figure 3. Make sure the rods protrude the base slightly and are consistent throughout all 4 arms, and be sure to have the motor wires facing outward.

Attach arms to motor bases

Figure 3: Attach arms to motor bases

Insert 4 nylon screws and nylon standoffs and attach the power module PM07 to the bottom plate using 4 nylon nuts as shown in Figures 4.

Attach power module

Figure 4: Attach power module

Feed the 4 motor ESCs through each of the arms and connect the 3-wires end to the motors shown in Figure 5.

Connect motors

Figure 5: Connect motors

Connect the ESCs power wires onto the power module PM07, black->black and red->red, ESC PWM signal wires goes to "FMU-PWM-Out". Make sure you connect the motor ESC PWM wires in the correct order. Refer to Figure 7 for airframe motor number and connect to the corresponding number on the PM07 board.

Figure 7: ESC power module and signal wiring

The color on top of the motor indicate the spin direction (figure 7-1), black tip is clockwise, and white tip is counter-clockwise. Make sure the follow the px4 quadrotor x airframe reference for motor direction (figure 7-2).

Figure 7: Motor order/direction diagram

Figure 7-1: Motor direction

Connect the 10 pin cables to FMU-PWM-in, the 6 pin cables to the PWR1 on the PM07 power module.

Flight controller/Power module PWM and Power connections

Figure 8: Power module PWM and power wiring

If you want to mount the GPS on the top plate, you can now secure the GPS mount onto the top plate using 4 screws and nuts.

Secure GPS mount onto top plate

Figure 9: Secure GPS mount onto top plate

Feed the PM07 cables through the top plate. Connect the top and bottom plate by using 4 U-shaped nylon straps, screws, and nuts on each side, ensure that the motor ESC cables are inside the U-shape nylon straps like Figure 10, keep the nut loose.

Figure 10-1: Feed power module cables through top plate

Connecting top and bottom plate

Figure 10-2: Connecting top and bottom plate

Push the arm tubes a bit into the frame and make sure the amount of protrusion (red square from Figure 11) are consistent on all 4 arms. Ensure all the motors are pointed directly upward, then tighten all the nuts and screws.

Arms 3

Put the hanger gaskets into the 4 hangers and mount them onto the bottom plate using 8 hex screws (Figure 11). The screw holes are noted by the white arrow in Figure 12. We recommend tilting the drone sideway to make the installation easier.

Hanger gaskets

Figure 11: Hanger gaskets

Battery Mount 4

Figure 12: Screw holes

Insert the slide bars onto the hanger rings (Figure 13). Assemble the battery mount and platform board and mount them onto the slide bars as shown in Figure 14.

Battery Mount 2: Slide bars

Figure 13: Slide bars

Battery mount on slide bars

Figure 14: Battery mount on slide bars

Mount the landing gear onto the bottom plate. We recommend tilting the drone sideway to make this installation process easier.

Landing Gear

Figure 15: Landing Gear

Use the tape and stick the GPS to the top of the GPS mast and mount the GPS mast. Make sure the arrow on the gps is pointing forward (Figure 16).

Figure 16: GPS and mast

Figure 16: GPS and mast

Mount the telemetry radio onto the top plate. Plug the telemetry cable into TELEM1 port and GPS module to GPS MODULE port on the flight controller. Plug the cable from PM07 FMU-PWM-in to I/O-PWM-outon the FC and PM07 PWR1 to POWER1 on the FC, as shown in Figure 17.

Pixhawk 4 wiring 1

Figure 17: Mount telemetry radio/plug in PWM and Power cables to Flight controller.

Please refer to Pixhawk 4 Quick Start for more information.

That's it. The fully assembled kit is shown below:

Assembled Kit

PX4 Configuration

:::tip Full instructions for installing and configuring PX4 can be found in Basic Configuration. :::

QGroundControl is used to install the PX4 autopilot and configure/tune it for the X500 frame. Download and install QGroundControl for your platform.

First update the firmware, airframe, and actuator mappings:

You will need to select the Holybro S500 airframe (Quadrotor x > Holybro S500).

QGroundControl - Select HolyBro X500 airframe

Actuators
You should not need to update the vehicle geometry (as this is a preconfigured airframe).
Assign actuator functions to outputs to match your wiring.
Test the configuration using the sliders.

Then perform the mandatory setup/calibration:

Ideally you should also do:

Tuning

Airframe selection sets default autopilot parameters for the frame. These are good enough to fly with, but it is a good idea to tune the parameters for a specific frame build.

For instructions on how, start from Autotune.

Acknowledgements

This build log was provided by the Dronecode Test Flight Team.

Holybro X500 Pixhawk4