Skip to main content

Gps Locosys Hawk A1

Raffaele Rossi

LOCOSYS Hawk A1 GPS/GNSS

The LOCOSYS HAWK A1 GPS/GNSS receiver is a dual frequency multi-constellation GNSS/GPS receiver compatible with PX4.

Main features include: - Concurrent reception of L1 and L5 band signals - Supports GPS, GLONASS,BEIDOU, GALILEO, QZSS - Capable of SBAS (WAAS, EGNOS, MSAS, GAGAN) - Support 135-channel GNSS - Fast TTFF at low signal level - Free hybrid ephemeris prediction to achieve faster cold start - Default 5Hz, up to 10 Hz update rate (SBAS at 5Hz update rate only) - Built-in super capacitor to reserve system data for rapid satellite acquisition - Three LED indicator for Power, PPS and Data transmit

Hawk A1

Where to Buy

Configuration

You can use the Hawk A1 as either main (primary) or secondary GPS system. The PX4 parameters should be set as below for each case.

Main GNSS

To use the Hawk A1 your main GPS device:

Parameter | Value | Description --- | --- | --- GPS_1_CONFIG | 102 (Telem 2 or another available serial port) | Configure main GPS port GPS_1_PROTOCOL | 1 (u-blox) | Configure GPS protocol SER_TEL2_BAUD | 230400 | Configure the serial port baudrate (here the GPS is connected to TELEM2 for instance)

Secondary GNSS

To use the Hawk A1 as an auxiliary GPS device (in addition to the main GPS):

Parameter | Value | Description --- | --- | --- GPS_2_CONFIG | 102 (Telem 2 or another available serial port) | Configure main GPS port GPS_2_PROTOCOL | 1 (u-blox) | Configure GPS protocol SER_TEL2_BAUD | 230400 | Configure the serial port baudrate (here the GPS is connected to TELEM2 for instance)

Wiring and Connections

The Locosys GPS comes with an 6-pin JST-GH Pixhawk-standard connector that can be inserted directly into either the GPS1 UART port (or GPS2 UART ports from Pixhawk FMUv5).

GPS cable

Pinout

The LOCOSYS GPS pinout is provided below. This can be used to help modify the connector for other autopilot boards.

| pin | Locosys GPS | pin | Pixhawk GPS 2 | | --- | ----------- | --- | ------------- | | 1 | VCC_5V | 1 | VCC | | 2 | GPS_RX | 2 | GPS_TX | | 3 | GPS_TX | 3 | GPS_RX | | 4 | NC | 4 | SDA | | 5 | NC | 5 | SCL | | 6 | GND | 6 | GND |

Status LEDs

Color | Name | Description --- | --- | --- Green | TX Indicator | GNSS Data transmission Red | Power Indicator | Power Blue | PPS | Precise Positioning Service active

Hawk A1 LEDs

Specifications

  • Receiver Type: 135-channel LOCOSYS MC-1612-V2b engine, GPS/QZSS L1 C/A, L5C, GLONASS L1OF, BeiDou B1I, B2a Galileo:E1, E5a SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN
  • Navigation Update Rate: Max: 5Hz default Max: 10 Hz
  • Positioning Accuracy: 3D Fix
  • Time to first fix:
  • Cold start: 28s
  • Aided start: EASY
  • Sensitivity:
  • Tracking & Navigation: -165 dBm
  • Assisted GNSS: EASY DGPS
  • Oscillator: 26Mhz TCXO
  • RTC crystal: 32.768KHz
  • Available Antennas: L1+L5 multi frequency antenna
  • Signal Integrity: L1+L5 GPS GLONASS GALILEO BEIDOU QZSS SBAS
  • Protocols & Interfaces:
  • UART/I2C: JST_GH Main interface, Switch internally.

Further info

Comments

0 comments

Please sign in to leave a comment.