Pid Tuning Guide Fixedwing

Fixed-wing Rate/Attitude Controller Tuning Guide

This guide explains how to manually tune the fixed-wing PID loop. It is intended for advanced users / experts, as incorrect PID tuning may crash your aircraft.

::: info Autotune is recommended for most users, as it is far faster, easier and provides good tuning for most frames. Manual tuning is recommended for frames where autotuning does not work, or where fine-tuning is essential. :::

Preconditions

• Trims must be configured first (before PID turning). The Fixed-Wing Trimming Guide explains how.
• Incorrectly set gains during tuning can make attitude control unstable. A pilot tuning gains should therefore be able to fly and land the plane in manual (override) control.
• Excessive gains (and rapid servo motion) can violate the maximum forces of your airframe - increase gains carefully.
• Roll and pitch tuning follow the same sequence. The only difference is that pitch is more sensitive to trim offsets, so trimming has to be done carefully and integrator gains need more attention to compensate this.

Establishing the Airframe Baseline

If a pilot capable of manual flight is available, its best to establish a few core system properties on a manual trial. To do this, fly these maneuvers. Even if you can't note all the quantities immediately on paper, the log file will be very useful for later tuning.

::: info All these quantities will be automatically logged. You only need to take notes if you want to directly move on to tuning without looking at the log files.

• Fly level with a convenient airspeed. Note throttle stick position and airspeed (example: 70% → 0.7 throttle, 15 m/s airspeed).
• Climb with maximum throttle and sufficient airspeed for 10-30 seconds (example: 12 m/s airspeed, climbed 100 m in 30 seconds).
• Descend with zero throttle and reasonable airspeed for 10-30 seconds (example: 18 m/s airspeed, descended 80 m in 30 seconds).
• Bank hard right with full roll stick until 60 degrees roll, then bank hard left with full roll stick until 60 degrees in the opposite side.
• Pitch up hard 45 degrees, pitch down hard 45 degrees. :::

This guide will use these quantities to set some of the controller gains later on.

Tune Roll

Tune first the roll axis, then pitch. The roll axis is safer as an incorrect tuning leads only to motion, but not a loss of altitude.

Tuning the Feedforward Gain

To tune this gain, first set the other gains to their minimum values (nominally 0.005, but check the parameter documentation).

Gains to set to minimum values

• FW_RR_I
• FW_RR_P

Gains to tune

• FW_RR_FF - start with a value of 0.4. Increase this value (doubling each time) until the plane rolls satisfactorily and reaches the setpoint. Back down the gain 20% at the end of the process.

Tuning the Rate Gain

• FW_RR_P - start with a value of 0.06. Increase this value (doubling each time) until the system starts to wobble / twitch. Then reduce gain by 50%.

Tuning the Trim Offsets with the Integrator Gain

• FW_RR_I - start with a value of 0.01. Increase this value (doubling each time) until there is no offset between commanded and actual roll value (this will most likely require looking at a log file).

Tune Pitch

The pitch axis might need more integrator gain and a correctly set pitch offset.

Tuning the Feedforward Gain

To tune this gain, set the other gains to their minimum values.

Gains to set to minimum values

• FW_PR_I
• FW_PR_P

Gains to tune

• FW_PR_FF - start with a value of 0.4. Increase this value (doubling each time) until the plane pitches satisfactory and reaches the setpoint. Back down the gain 20% at the end of the process.

Tuning the Rate Gain

• FW_PR_P - start with a value of 0.04. Increase this value (doubling each time) until the system starts to wobble / twitch. Then reduce value by 50%.

Tuning the Trim Offsets with the Integrator Gain

• FW_PR_I - start with a value of 0.01. Increase this value (doubling each time) until there is no offset between commanded and actual pitch value (this will most likely require looking at a log file).

Adjusting the Time Constant of the Outer Loop

The overall softness / hardness of the control loop can be adjusted by the time constant. The default of 0.5 seconds should be fine for normal fixed-wing setups and usually does not require adjustment.

• FW_P_TC - set to a default of 0.5 seconds, increase to make the Pitch response softer, decrease to make the response harder.
• FW_R_TC - set to a default of 0.5 seconds, increase to make the Roll response softer, decrease to make the response harder.

Other Tuning Parameters

The most important parameters are covered in this guide. Additional tuning parameters are documented in the Parameter Reference.